My Cart:

0 item(s)
You have no items in your shopping cart.

0

Welcome to our online store!

Saturn Vue Ion/Ion Red Line Chevrolet Malibu 4/ MP50115 Fuel Injectors

Quick Overview

The Remanufacturing Process

Not all injectors are the same! Therefore, the remanufacturing process is not the same for all injectors! Our 14 years of experience, allow us to determine the best process for the type of injector to be remanufactured.

Multec Injectors:

  • Additional reverse flow cleaning time

Bosch Nozzle type:

  • Additional Ultrasonic cleaning time

Delphi, Nippon Denso, Bosch pencil style:

  • Additional reverse flow cleaning time

TBI Injectors:

  • Disassembled and recalibrated
  • (An alternate core or a new part substitutes all part numbers that are known to have external leaking problems or intermittent flow due to poor original design.)

All Injectors are Electronically Tested:

Coils are tested for correct electrical resistance and for coil weakness. Good units are then disassembled (Micro filter, seals, pintle caps and plastic spacer are removed.)

Internal Ultrasonic Cleaning:

Sets of 8 injectors are simultaneously cleaned in ultrasonic tanks specifically designed to clean fuel injectors. The injectors are placed in the ultrasonic tank with a cleaning solvent while they are electronically activated. The ultrasonic waves are allowed into the fuel injectors to clean and remove all internal contaminants. External Cleaning: Once the internal contaminants have been loosened up then the fuel injectors are completely submerged in bigger tanks to complete the ultrasonic cleaning internally and externally.

Back Flushing:

Once the injector has been cleaned ultrasonically, all units are individually back flushed to remove the broken dirt particles. These particles can not be removed thru the injection orifices so they are driven out thru the inlet of the injector.

Reverse Flow Pressure Cleaning:

(This extra step is very critical, especially on all GM Injectors). All injectors are then mounted on the flow bench in an inverted position allowing them to reverse flow at a considerable pressure. We run a high performance injector cleaning solvent thru the injectors for 30 minutes, completing the cleaning process. This process assures us that all dirt particles completely removed from the injector. No other company performs this procedure.

Leak Test:

Injectors are now mounted on the flow bench in the correct position to begin the testing procedures. We apply 60 PIS of pressure (more than a regular multi-port fuel injection system) and maintain this pressure with no signal to the injectors for 30 seconds. This test is to ensure that there are no fuel leaks.

Spray Pattern Test:

The spray patter is then visually inspected applying pressure and holding the injectors statically open for correct spray form (Spray pattern may be different in some injectors).
To determine if any flow differences are caused by dirt blockage or defective injector components we perform two additional measuring test:


1 Static Flow Test:

The amount of fuel delivered by each injector is measured by holding the injector continuously open at a constant pressured (normally 44 PSI / 3 BAR) for a predetermined period of time). During this test if there is a flow difference of more than 4% it is likely caused by dirt blockage since the injector components (spring& coil) are not being utilized at this time.

2 Dynamic Flow Test:

The amount of fuel delivered by each injector is measured by activating the injector at different pulse cycles and RPM’S at a constant pressure (normally 44 PSI / 3 BAR) for a predetermined period of time. (This test better simulates actual daily driving conditions). If the flow difference in this test is greater that the difference of the static test this would indicate faulty injector components (spring or coil).

Painting / Polishing:

Depending on the original manufacturer presentation, the injectors are either painted or polished to give the best cosmetic appearance possible

New Components:

Injectors are now assembled with new replaceable components (Filter baskets, pintle caps, O-rings and seals)

Final Tests:

A final test is now performed with all new components installed. The purpose of this test is to make sure the filter basket; o-rings, seals and pintle caps are positioned correctly and are not disturbing the flow or the spray pattern of the injector.

Lubrication & Packaging:

Injectors are lubricated with special oil and protective caps are placed on both ends to extend the shelf life and assure that when they are installed in the vehicle they will be in optimum operating condition. Each injector is individually bagged.

$134.99
SKU: C9541DBB-2955-4DAA-9258-9D8197C317A1
AdID: 32784

Availability: 350 item(s)

Details

Aus Injection MP50115 Fuel Injector
Part Brand: Aus Injection
Manufacturer Part Number:

This Listing is for 4x Part# MP50115

  MALIBU   2004-2005
     2005 L4-134ci 2.2L F/I Vin F 
     2004 L4-134ci 2.2L F/I Vin F   
 
 
 SATURN  2002-2005
   ION   2003-2004
     2004 L4-134ci 2.2L F/I Vin F   
     2003 L4-134ci 2.2L F/I Vin F 
 
   ION RED LINE   2004-2004
     2004 L4-122ci 2.0L F/I S/C Vin P  
 
   VUE   2002-2005
     2005 L4-134ci 2.2L F/I  
     2004 L4-134ci 2.2L F/I Vin F   
     2003 L4-134ci 2.2L F/I   
     2002 L4-134ci 2.2L F/I     

   2004-2005
     2005 L4-134ci 2.2L F/I Vin F    4 per Vehicle
     2004 L4-134ci 2.2L F/I Vin F    4 per Vehicle
 
 
 SATURN  2002-2005
   ION  2003-2004
     2004 L4-134ci 2.2L F/I Vin F    1 per Vehicle
     2003 L4-134ci 2.2L F/I Vin F    1 per Vehicle
 
   ION RED LINE  2004-2004
     2004 L4-122ci 2.0L F/I S/C Vin P    1 per Vehicle
 
   VUE   2002-2005
     2005 L4-134ci 2.2L F/I    4 per Vehicle
     2004 L4-134ci 2.2L F/I Vin F    4 per Vehicle
     2003 L4-134ci 2.2L F/I    4 per Vehicle
     2002 L4-134ci 2.2L F/I    4 per Vehicle
 
 


 

Part Brand: Aus Injection
Manufacturer Part Number: MP50115
Portions of this page provided by Epicor Inc. and may be subject to copyright

Additional Information about Aus Injection MP50115 Fuel Injector
Portions of this page provided by Epicor Inc. and may be subject to copyright


Product Details
Sub Type:   Fuel Injector

 


Fitment Details

Year Make Model Trim Engine Notes
2004 Chevrolet Malibu Base Sedan 4-Door 2.2L 2198CC 134Cu. In. l4 GAS DOHC Naturally Aspirated
2005 Chevrolet Malibu Base Sedan 4-Door 2.2L 2198CC 134Cu. In. l4 GAS DOHC Naturally Aspirated
2002 Saturn Vue Base Sport Utility 4-Door 2.2L 2198CC 134Cu. In. l4 GAS DOHC Naturally Aspirated
2003 Saturn Vue Base Sport Utility 4-Door 2.2L 2198CC 134Cu. In. l4 GAS DOHC Naturally Aspirated
2004 Saturn Vue Base Sport Utility 4-Door 2.2L 2198CC 134Cu. In. l4 GAS DOHC Naturally Aspirated
2005 Saturn Vue Base Sport Utility 4-Door 2.2L 2198CC 134Cu. In. l4 GAS DOHC Naturally Aspirated